De firmware van het Homematic IP Access Point is geüpdatet naar versie 3.0.16. Deze update bevat twee bugfixes: een voor een probleem met multicast routing, en een voor een verkeerde LED indicatie na ontvangst van data van een lookup server. De changelog bevat alle informatie van de huidige en eerdere firmware updates. De update wordt spoedig beschikbaar via de Homematic IP app. Voor gebruikers van de CCU3 wordt de update zichtbaar via de Homepage van de WebUI.
C H A N G E L O G
-----------------
Please note: Only use the firmware file in connection with the current software-version of the CCUx!
Device: HmIP-HAP - Access Point
alte Bezeichnung: YOU-HAP-TTU
Company: eQ-3, Maiburger Str. 29, 26789 Leer, Germany
Version 3.0.16 - 2023-06-14
--------------------------------------------------------------
** Bugfix
* Multicast routing problems
* LED sequence wrong after get data from lookup server
Version 3.0.12 - 2023-05-31
--------------------------------------------------------------
** Bugfix
* Problems at Update
Version 3.0.10 - 2023-04-21
--------------------------------------------------------------
** Bugfix
* Times between lookup requests become too large
* After reboot (power) sometimes both APs connected to cloud
* No lookup request after get a crrfd url that is too long
* Time at close connection with 0xffff wrong
Version 3.0.4 - 2023-03-22
--------------------------------------------------------------
** Bugfix
* Encrypted frames not send to cloud
* The access point gets stuck in an endless loop when an update is triggered by Netfinder, but no different version is available on the update server.
* Backbone frames payload length wrong
** New Feature
* New parameters for multicast filter
* Connection to the Cludserver, LockupServer and Updateserver via IPv6 possible
* Use return code when closing the WebSocket to the AP for indication if the route is still valid.
** Improvement
* send destination unreach with LHL = 7-x
Version 2.4.28 - 2022-09-16
--------------------------------------------------------------
** Bugfix
* The access point sends frames to the server that are too long.
* Replies to frames from the server are lost.
** Improvement
* Set different timeouts for backbone Routers and backbone devices
Version 2.4.24 - 2022-05-12
--------------------------------------------------------------
** Bugfix
* The HAP treis to send a frame to all wired devices via any router
Version 2.4.20 - 2022-04-06
--------------------------------------------------------------
** Bugfix
* The HAP will reboot if it does not receive a response to an Inclusion Accept.
Version 2.4.18 - 2022-03-29
--------------------------------------------------------------
** Bugfix
* The HAP sends a route management frame with its own address marked as unreachable.
Version 2.4.16 - 2022-01-26
--------------------------------------------------------------
** Bugfix
* The access points (HAP/DRAP) always send the Manufacturer Code 0x01 (EQ3) in the Inclusion Request, even with OEM variants.
* Device becomes continuous BURST transmitter in case of cloud failure
* HAP answers status frames (ARR) with burst frames.
** New Feature
* Forward backbone route management frames to the cloud server
Version 2.4.12 - 2021-07-27
--------------------------------------------------------------
** Bugfix
* The HAP tries to start a sequence number validation on all frames and takes the destination address of the receiving frame as the source address.
Version 2.4.10 - 2021-07-15
--------------------------------------------------------------
** Bugfix
* FactoryReset first button press duration too long
Version 2.4.8 - 2021-06-29
--------------------------------------------------------------
** Bugfix
* KeyVisual key press data for long button press wrong
** Improvement
* Stronger evaluation of the RSSI value during routing
Version 2.4.4 - 2021-04-28
--------------------------------------------------------------
** Bugfix
* HTTP client hangs, if the previous connection was not closed.
* The access point interrupts the connection to the cloud server if the lookup server has delivered an incorrect URL.
* Incorrect KeyVisual signal when the AP disconnects from the cloud server.
* Wrong priority for frames to event listener
* The AccessPoint sends a response to an empty RM V1 request.
* HAP glows permanently turquoise in a Singel HAP installation
* Factory reset is also possible during operation.
* Fehler bei nicht erreichbarer UpdateURL
* Invalid Tcp/IP packet in the web bootloader.
* Websocket connection delay is only applied after restart.
* HAP do not respond to IGMPv3 Membership Queries
** New Feature
* Request routing information over HAP protocol
* Live OTAU Service
** Improvement
* Improve system behavior when HmIP-HAP has no internet connection.
Version 2.2.24 - 2020-12-16
--------------------------------------------------------------
** Bugfix
* Frames can no longer be sent. The stack remains in the busy state.
Version 2.2.18 - 2020-10-07
--------------------------------------------------------------
** Bugfix
* OTAU: "Update Data" frames are send with burst.
Version 2.2.16 - 2020-09-23
--------------------------------------------------------------
** Bugfix
* Web-Bootloader cancels download of CoProzessor update.
* Download of update files will not start, if FIN,ACK from checkversion is not acked.
Version 2.2.12 - 2020-08-26
--------------------------------------------------------------
** Bugfix
* Multicast Readressing is also applied to INTERFACE_LOCAL/CLOUD
Version 2.2.10 - 2020-08-24
--------------------------------------------------------------
** Bugfix
* If the application is defective, an incorrect application version is reported to the update server.
** Improvement
* No longer route cyclic multicast frames.
* Flashing behaviour when the centre is not accessible (flashing turquoise)
Version 2.2.4 - 2020-08-07
--------------------------------------------------------------
** Bugfix
* The device-specific configuration can no longer be retrieved with Netfinder.
Version 2.2.0 - 2020-07-16
--------------------------------------------------------------
** Bugfix
* With the custom lookup address, the path is not processed correctly.
** New Feature
* Advanced Routing
** Improvement
* Change the default update URL
* Improve the connection to the cloud server.
Version 2.2.2 - 2020-07-24
--------------------------------------------------------------
** Bugfix
* Wrong app sequence counter in status response frame.
** Improvement
* Do not accept frames to AnyRouter if it is known that it is not routed.
Version 2.0.40 - 2020-10-05
--------------------------------------------------------------
** Bugfix
* Download of update files will not start, if FIN,ACK from checkversion is not acked.
Version 2.0.36 - 2019-10-16
--------------------------------------------------------------
** Bugfix
* The HAP crashes and restarts when DHCP is switched off.
Version 2.0.34 - 2019-10-11
--------------------------------------------------------------
** Bugfix
* If the ICMP ping fails, but the lookup server query succeeds, the KeyVisual color is not updated.
* The local bootloader returns a wrong value during the update.
Version 2.0.32 - 2019-10-08
--------------------------------------------------------------
** Bugfix
* No connection to the server is established and the KeyVisual lights up yellow permanently.
** Improvement
* To test the Internet connection, an attempt is made to send a ping to the lookup server; if the ping fails, an attempt is made to establish a connection anyway.
Version 2.0.26 - 2019-07-23
--------------------------------------------------------------
** Bugfix
* With the custom lookup address, the path is not processed correctly.
* HAP firmware stops after a FactoryReset is cancelled.
* FactoryReset has no timeout.
Version 1.2.26 - 2020-10-06
--------------------------------------------------------------
** Bugfix
* Download of update files will not start, if FIN,ACK from checkversion is not acked.
Version 1.2.12 - 2018-04-19
--------------------------------------------------------------
** Bugfix
* the configuration data will sometimes be corrupted during the update, causing a factory reset
* Look up server is requested just one time after startup
--- END OF FILE ---