FW update: Draadloze drukknop met 2 knoppen HmIP-WRC2 v1.18.2

C H A N G E L O G
-----------------

Please note: Only use the firmware file in connection with the current software-version of the CCUx!

Device: HmIP-WRC2 - Wall-mount Remote Control - 2-button

Company: eQ-3, Maiburger Str. 29, 26789 Leer, Germany

Version 1.18.0/1.18.2 2022-02-14/2023-02-07
--------------------------------------------------------------
** Bugfix
* FactoryResetTiming to long

** New Feature
* Change of the bidirectional cyclical status transmission interval to extend the battery lifetime.
* Support of "Security Plus" - Disable active alarm system although the cloud is offline

** Improvement
* General improvements - Code optimisation

Version 1.16.2 - 2020-10-26
--------------------------------------------------------------
** Bugfix
* If AC is not responding on startup, the device is blocking until routing is done.
A triggered switch command is sent after that but without optical feedback.
* Device is not waiting the ARR timeout after optical feedback (only devices with optical feedback at MAC level)

Version 1.16.0 - 2020-10-16
--------------------------------------------------------------
** New Feature
* add support for optical feedback after MAC-sending is done (all MAC-ACKs received or MAC-Ack failure)

Version 1.14.10 - 2020-07-09
--------------------------------------------------------------
** Bugfix
* USC with long keystroke is only sent after the key is released (if more Groups are activ)
* RemoteControl freeze after 2nd long keystroke on same channel ((same fix as for bug in the line before)
* Device sends further switch command after ReportLinkPartnerProblem was send
* STOP-Button retriggers SwitchCommand which was send before from other Channel (same fix as for bug in the line before)

Version 1.14.8 - 2020-07-02
--------------------------------------------------------------
** Bugfix
* If a burst partner is linked to channels > 6, a long keypress leads to a deadlock
* Device send USC to Linkpartner on long keystroke as long button is pressed

Version 1.14.6 - 2020-06-18
--------------------------------------------------------------
** Bugfix
* fixed wrong check of stop push button for

Version 1.14.4 - 09.06.2020
--------------------------------------------------------------
** Bugfix
* Device teststatus not longer set to 0 by default

Version 1.14.2 - 29.05.2020
--------------------------------------------------------------
** Bugfix
* Device sends switchCmd with long keystroke only on botton release to HmIP link partner
* If add a LP to Channel < 7, Linkpartner on channel > 6 will not work anymore

Version 1.14.0 - 08.05.2020
--------------------------------------------------------------
** Modification
* support for HmIP-HDRC

Version 1.12.4 - 29.11.2019
--------------------------------------------------------------
** Modification
* support for HmIP-WRCCR

Version 1.10.2/1.10.4 - 20.11.2020/24.11.2021
--------------------------------------------------------------
** Bugfix
* FactoryResetTiming to long

** New Feature
* Change of the cyclical transmission interval to extend the battery lifetime.
* Update HMOS to 1.40.0

Version 1.10.0 - 02.03.2018
--------------------------------------------------------------
** Bugfix
* Sendeverhalten bei langem Tastendruck fehlerhaft
* Fehler im Sendeverhalten, wenn Partner spät antworten

** New Feature
* HmIPW: Neuer Operation-Mode
* Zentralen basierte Lösungen und Lösungen ohne Zentrale (Installateur)

** Improvement
* Alarmbackup durchführen wenn Access Point/Zentrale ein NAK auf ein
Unconditional Switch Command sendet
* update HMOS to V1.26.0

Version 1.6.0 20170823
--------------------------------------------------------------
** Bugfix
* if one link partne is
unreachable the device goes to sleep directly and is not
waiting for app answers of other link partners

** Improvement
* update HMOS to V1.20.3

Version 1.4.2 20161216
--------------------------------------------------------------
** Bugfix
* HMOS now ignore stay awake bit for
frames that are looped back internal
* statusinfo frames are send with the "normal"sequence
number ->
after every status info frame the status info sequence
counter is incremented, but the normal counter is put in
the status frame. so every status info is send with the
same sequence number as long no "normal" frame is send.
The ACKs of the status info frames are not accepted as
the sequence number of the ACK frame and the internal
status info sequence number doesn't match

** Improvement
* update HMOS to V1.18.2

Version 1.4.1 20160422
--------------------------------------------------------------
** Bugfix
* Fixed bug that device waits arr
timeout before signaling tx status (red or green)
* Device now accepts answers from SNC/HAP for switch commands

Version 1.4.0 20160329
--------------------------------------------------------------
** Modifications
* Move project to Git
* Update HMOS to V1.16.0
* Bootloader is V1.8.0

Version 1.2.8 20160120
--------------------------------------------------------------
** Bugfix
* If no link partner is available, a report link partner
problem frame is send. If a new kepress is detected
while the timeout for the link partner problem frame,
the device sends a config request after the timeout and
after the tx tries of the kepress.
* The report link partner problem frame now includes a
link partner ip.

Version 1.2.7 20160118
--------------------------------------------------------------
** Bugfix
* If the APPLICATION_cb_tx_UncndSwCmd
has the state HMIP_MAC_STATUS_FAILED the sleep_delay is
not set and the no further button presses are accepted.
The LED does not stop blinking

** Modifications
* First cyclic interval event is not longer
triggered directly after boot up, but after the minimum
interval + random time.

Version 1.2.6 20160111
--------------------------------------------------------------
** Modifications
* Changed HMOS to version 1.12.1
* Changed KRC4 to EFM32G210F128

Version 1.2.5 20151002
--------------------------------------------------------------
** Modifications
* Adapt the factory reset signalling
according to the changed specification.
* The printf function calls are not removed if DEBUG_EFM
is not defined. The printf function is now called by a
DEBUG_PRINTF macro if DEBUG_EFM is defined otherwise the
macro is empty. Saves 3.5 k flash space.
* Changed full rx timeout to a fix value of 1000 s for a
normal unconditional switch command due to the changes
in the HMIP_APP_send_to_link_partners_async function.
* Changed full rx timeout to a fix value of 45 s for
status info, config request and send link partner problem
to met the router timeouts.
* Since HMIP_APP_send_to_link_partners_async sends now
always with ARR-bit the handling of long key presses has
changed. The FRAMES_create_unconditional_switch_command
no longer need to set the arr bit, this is done in the
application task.
* set sleep delay to 0 if there is only one partner and it
isn't available -> free the keys busy flag
* Renamed APPLICATION_cb_tx_UncndSwCmd_multicast to
APPLICATION_cb_tx_UncndSwCmd_unidirectional.

** Comments
* Modified compiler settings for KRC4 so that they are the
same as for PBS2.

Version 1.2.4 20150817
--------------------------------------------------------------
** Bugfix
* If the time for partner communication
exceed 10 seconds (e.g. 20 burst partners which are not
reachable) the application go to sleep after arr timeout.
The sleep timeout is now set if after starting the
transmission and retriggered in the tx callback. The trx
is now initially set to full rx for arr + 1 seconds and
is retriggered in the tx callback with aar + 1 second.

* The answer of the AC on a Request
Config Update is no handled by the application. This
causes that the device go to sleep after the reception
of the answer. By now the devices waits for ARR-Timeout.

** Modifications
* The application now sends a "report
link partner problem" frame if the partner has not been
reached(No MAC-ACK). A Config Request is only send if the
link partner answers with ANSWER_NAK_INVALID_CHANNEL or
ANSWER_NAK_PEER_UNKNOWN.

Version 1.2.3 20150724
--------------------------------------------------------------
** Modifications
* modified testmode for the HMIP-KRC4

Version 1.2.2 20150701
--------------------------------------------------------------
** Bugfix
* if the firmware is programmed to a new oder full erased controller,
the firmware hang up while loading the channel parameters. The
application and the key task always got a RETURN_BUSY from HMOS.
This error might be come up with the change to the HMOS lib. The
application and the key task now wait 10 ms between each call of
the PARAMETER_get_param_sequence_async function, this seems to help.

Version 1.2.1 20150623 (not released)
--------------------------------------------------------------
** Bugfix
* The channels 3 and 4 of the KRC4 were not handled
in the APPLICATION_validate_parameters_async function. So it returns
CALLBACK_FAILED and the stack sends a NAK.

Version 1.2.0 20150612
--------------------------------------------------------------
** Modification
* Changed to HMOS-LIB V1.10

** Comments
* Added APPLICATION_emc_led_success due to changes in HMOS / Stack.
* The Callback of the LED module has now an state and is called also
if the led program is aborted by a new program. This might lead to
failures in the device behaviour.

Version 1.0.4 20150409
--------------------------------------------------------------
** Comments
* Increased Version number for OTAU testing.

Version 1.0.3 20150409
--------------------------------------------------------------
** Modification
* Changed HMOS to V1.6.2

Version 1.0.2
--------------------------------------------------------------
** Modification
* Added support for request status frame

** Bugs
* Corrected a bug with the sequence number check.

Version 1.0.0 20150320
--------------------------------------------------------------
** Modification
* Added support of MAC status HMIP_MAC_STATUS_OK_ROUTED (tx callbacks)
* Changed Parameter ENABLE_ROUTING default value to 1 as the default
value in HMOS is 1 and the application now has to set the value

** Bugs
* Corrected the device behaviour if the Parameter LONG PRESS TIME is
0 (disabled)

--- END OF FILE ---