FW update: Dimmer voor merk-wipvlak HmIP-BDT v2.2.4

C H A N G E L O G
-----------------

Please note: Only use the firmware file in connection with the current software-version of the CCUx!

Device: HmIP-BDT - Homematic IP
Dimmer mit Phasenabschnittsteuerung für Markenschalterserien

Company: eQ-3, Maiburger Str. 29, 26789 Leer, Germany

Version 2.2.4 - 2023-11-10
--------------------------------------------------------------

** Bugfix
* Fixed error which leads to an boot failure under some special conditions.

Version 2.2.0 - 2023-06-08
--------------------------------------------------------------

** Bugfix
* The ON_MIN_LEVEL parameter is evaluated inconsistently for a DEC and a direct link.

** New Feature
* Add separate LED mode with additional configuration parameters for a better dimming behaviour

Version 2.0.0 - 2022-12-06
--------------------------------------------------------------

** Bugfix
* Wrong evaluation of the event counter with multiple links between sensor and actuator
* In a switching group, only the first channels are switched on
* With the settings "Anzahl der auszulassenden Statusmeldungen = 0" and "Anzahl der auszulassenden,unveränderten Statusmeldungen = 0" the status is not transmitted in 2 to 3 minute intervals
* Device sends answers-frame on a TimeInfo from AC to "any-router"-address
* If the switch-on and switch-off times in the Easy Profile are set to "Not active" at the same time, the device hangs up.
* Rocker switch no longer responds after frequent operation
* System LED signals error (red) if rocker switch is linked to internal channel and 2 or more external channels
* Homematic IP actuators trigger, due to the astro function, one hour delayed or prematurely on the day of the time changeover.
* A TimeInfo frame with ARR-Bit will not be answered
* Wrong behaviour if a link partner is answering late
* Device does a reboot if factory reset is aborted
* device uses OFF_LEVEL of a direct link for direct execution command if level of direct execution is 0
* Wrong order of datatypes in the statusinfo frame
* The Weekprogram astro times doesn't work correctly with negative latitude or longitude
* After an OTAU reboot the inclusion requests are send to address 0x000000 sometimes

** New Feature
* Implement channel parameter for setting the Dimm-Min-Level.
* Switch-off ramp via central programs or automation.
* Rework AppSequenceCounter validation to a counter range check
* Support of HmIPW operation mode
* Support of systems and solutions without a central unit (installer solution)

** Improvement
* Switch from external to internal oscillator
* The time information telegram does not contain a note about the sommer / winter time change.
* HmIP actuators with default links as button pair, should also have ABORT_EVENT_SENDING_CHANNELS as default in pairs.
* If possible, send multicasts only to PARTNER_ALL_WIRED_DEVICES instead of to PARTNER_ALL_DEVICES.
* Changing driving directions with HmIP UP actuators via parameters.
* Modify event counter check to meet current specification
* Improve switch command functionality by new implementation of local loopback, adding command cancelation and using node sending functionality
* All PowerUp parameters, that are listed in list 3 of the device, must be supported.
* Changed default values for Powerup action parameters

Version 1.6.0 - 2017-11-21
--------------------------------------------------------------

** Bugfix
* Homematic IP actuators trigger, due to the astro function, one hour delayed or prematurely on the day of the time changeover.
* A TimeInfo frame with ARR-Bit will not be answered
* Device does a reboot if factory reset is aborted
* device uses OFF_LEVEL of a direct link for direct execution command if level of direct execution is 0
* Wrong order of datatypes in the statusinfo frame
* The Weekprogram astro times doesn't work correctly with negative latitude or longitude
* After an OTAU reboot the inclusion requests are send to address 0x000000 sometimes

** New Feature
* Rework AppSequenceCounter validation to a counter range check
* Support of HmIPW operation mode
* Support of systems and solutions without a central unit (installer solution)

** Improvement
* All PowerUp parameters, that are listed in list 3 of the device, must be supported.
* Changed default values for Powerup action parameters

Version 1.4.8 - 2017-08-01
--------------------------------------------------------------

** Bugfix
* Implement missing support of the direct execution commands LOCK and UNLOCK

* After the first time NACK answer, all answers are NACK
* Device hangs up while installing update V1.2.2
* Wrong applications sequence number after a long keypress
* If not included, a long keypress triggers an inclusion request all 250 ms
* Direct execution commands with speciale value level "old value" is not handled correctly
* Device sends answers on multicast commandand on commands without arr bit in generally

* If a sending device (RC etc. ) is connected to more than one virtual channel, only the first channel is switching.

* Modify power up jump targets to match the power up jump targets of the switch actuators
* Na answer on a configuration commit frame

--- END OF FILE ---